I had a day of beautiful weather I wanted to take advantage of on Saturday, so I woke up early, walked the dog, and got my chores done early so I could get outside.
A lot of the highlights are covered in the video, but I’ll bullet-point them here:
- The three spare wheels I’ve been storing under the back porch for ten years, and often considered hauling off to the trash, came in super-handy for the Travelall: they’re the same bolt pattern and they all hold air, so I swapped out the shredded flats on the truck and got it off the ground. There’s still one that’s flat but I’m going to put the one good tire that came with the truck on there and shoot it with some stop-leak. This means that the wheels won’t fit the red Travelall and I can toss them all out when it’s time to get rid of this truck. The green truck now looks 6% less redneck.
- Jacking up the truck in back to swap said tires, I found that the top leaf in the driver’s spring pack was cracked in half. I may still try to pull those off to have re-arched at some point, but I have to measure them all first to see if they’ll fit the Red Bus.
- I tore the carpet off the floors front and rear, and found lots of rust underneath. There are two huge sections under the front seats that are completely gone, and giant patches of rust in the back. My tub is definitely in much better shape here.
- It always takes more time to get parts off a truck than you think. As long as I’ve been doing this, I’m always stupidly optimistic in terms of what I believe I can accomplish. Putting in a full day Saturday, I got all of the trim off, the roof rack removed, four aluminum sill plates, the visors and rearview mirror, the headlights, tail lights, and both front marker lights. And then I spent two hours getting the driver’s fender off. It’s in excellent shape and should clean up really well, so it was definitely worth it. I got about half the bolts off the passenger side before I had to pack things in; the most painful bolts need to soak in PBblaster for a week or so. Somehow I thought I’d have half the truck apart already.
- I’m going to have to hook a battery up to try and lower the rear window to get the gate open. The chances of this being successful are about 1000/1. When that doesn’t work, I’ll have to get a thick Phillips-head screwdriver on the 6-8 bolts at the bottom of the inside panel to get access to the motor. The chances of this being successful are 500/1. But the tailgate—and more importantly, the glass—are very much worth the effort. Jeff J. tells me the glass is curved and very hard to find.
- Jeff also tells me the power steering box on this truck won’t work on my truck; this truck (with IFS) has a boxed frame while mine is channeled, and there are differences in where the steering box goes and how it mounts. Rats.
- Also, the front grille assembly won’t fit my truck; the 1965+ trucks had a square opening in the sheet metal while mine is scalloped on the ends. Doesn’t matter, I’m taking it all off anyway.
- I pulled on the fan blade to see if the engine would turn, and it’s stuck tight. Once I can drain the radiator and pull that out, I’ll have room to see if I can get a socket on the crank bolt and put a breaker bar on it. Maybe I’ll pull the plugs and soak the cylinders in Marvel Mystery Oil; we’ll see.
- I wasn’t able to get the cowl cover off to put the borescope in to check out the vents down there, but judging by the rusted edges on each side and the pile of debris that fell out when I opened the driver’s vent, I’d guess they’re pretty well shot.
- I did a fair bit of ADHD scatterbrain picking before I settled down and focused on a few main items. I had actually written down a list based on a strategy of keeping the outer shell together to keep it looking respectable while I take all of the interior parts out, but hubris got the better of me. The driver’s fender is now hung with one bolt. I’m going to do the same with the passenger side, then work on the front clip. Inside the engine bay there are a lot of parts that will stay behind, and I’ll get as much as I can out of there before I start dismantling the interior.
So in rough order, here’s the basic plan:
- Get the passenger fender off
- Get the inner fenders ready to pull off
- Drain the coolant, and pull the radiator out
- Remove the heating box from inside the cab
- Pull the plugs and put some Marvel Mystery oil in the cylinders; see if the engine will turn
- Continue pulling the front cowl off
- Put a battery in and see if the rear window will go down
- If yes, then open the tailgate and get the glass out
- If no, then get a larger screwdriver and try to get the bolts off to open the access panel
- Remove the rear tailgate
- Pull the rear bumper off
- Remove the entire power steering assembly
- Pull the brake booster assembly
- Pull out the front bench and base
- Dismantle and remove the entire dashboard
- Pull the steering wheel out
- Pull out all internal trim
- Ceiling surround channel
- Extra ceiling hoops
- Armrests, other minor trim
- Pull the front bumper off
- Take the doors off
- Take the hood off
- Take the inner and outer fenders off
- Maybe pull the good leaf spring off?