I spent Saturday down at Bob’s with my brother in law, working to get the Chrysler back in the garage. The engineering problem I faced was how to push a 4,300 lb. car back up a slight incline into the garage, while also moving it laterally by about ten feet. The solution I came up with involved a hammer drill, several concrete bits, lag bolts and barrels, and a cheap Harbor Freight winch with a remote.
After loading up on the supplies, Glen and I opened up the shiny new garage door and set up for the installation. I measured out two holes for the baseplate and had him start drilling while I assembled the winch. After a couple of tries with different bits and an adjustment in hardware which required a return trip to Lowe’s and a stopoff for tacos.
When we got back, the new bits we bought made relatively short work of 45-year-old concrete, and I was able to anchor the winch into the floor. I pulled the battery from the Chrysler and used that for power (it’s been on a tender since I bought it) and we played out the line to the back of the car. The winch wasn’t powerful enough to pull the car by itself, but with three of us pushing, it was the extra power we needed—as well as a safety measure in case the car got away from us. I hauled the wheel over hard to correct the position and then we pushed/pulled the car up about 3/4 of the way inside. With that done, we jacked up each corner and put it on the dollies so that we could push it to the far side of the garage, as out of the way as possible.
Sunday morning I got out to the Travelall and cleaned off the inside roof with acetone before covering the whole thing with Rust-Stop. While that cured, I pulled the driver’s wheel and cleaned the outside face of the driver’s inner fender with the wire wheel. That was covered with Rust Encapsulator, and while that dried I painted the frame with chassis black. And while the can was open I painted the frame on the passenger side where the gas tank will go.
Inside the cab, I used some chalk to mark out where the sound deadener was going to go, and cut a sheet of kraft paper to test the measurements. After some adjustments I flattened the first sheet out and aligned the center with the centerline of the roof, and peeled a little of the backing off to set it in place. It took some work to get everything oriented correctly, and then I peeled one side off to set it permanently. Give or take 1/8″ on either side, I got it aligned almost perfectly; using the long edge to align the second and third sheets, I made it to the back of the truck centered on the rear doors.
By that point it was getting dark and cold, so I closed up the truck and moved into the basement to work on the base of the rear bench seat. After reviewing some how-to videos to refresh my memory, I cut burlap, foam and carpet padding down to fit the seat and attached the burlap to the frame with some hog rings. Then I stretched the cover over the bench as best I could, working to get the scallops in the back edge into place.
Stretching the cover and clipping it in with the hog rings is exactly the same process as stretching a canvas or mesh for screenprinting: start at the middle of each edge and work your way outwards. Again, the trickiest parts were the indents where the seat is scalloped to avoid the wheel wells, but I realized I could compress the whole seat by kneeling on it and used that to pull the fabric around to the attachment bars.
Overall I’m pretty happy with the results for my first attempt. I put the carpet padding on top of the foam, but Jeff tells me it’s supposed to go underneath, which is what I’ll do with the upright part of the seat. For this I wanted it to be firm directly underneath, and I wasn’t aware there was a firmer foam available for the seat when I bought my materials. I’ve got to carefully add some small holes for the four hinge bolts and the bump stops, which makes me nervous, but Jeff tells me it should be fine.
So next up I have to disassemble the upright for the rear seat and prep it for covering, which means I have to hit it with the wire wheel and spray it down with Rust Converter.
I’m headed north to see my family for Thanksgiving, and there’s a junkyard near my sister’s house with some ancient IH iron, including this rusty Travelall panel truck. I’m not sure what to expect, but he says he’s got other IH stuff in there somewhere, so it should be a fun day for bushwhacking. I bought a cordless angle grinder on contingency but I’m going to leave it in the box so that I can return it if I don’t need it.
Looking at the dashboard, it’s a ’62 or earlier, so it’ll be interesting to get a look at the front clip. At first blush the stuff I see that would be worth something would be the barn doors, but they look pretty rough. Just looking at this photo, the things I see that might be worth picking would be:
- The barn doors, if they’re salvageable
- if not, the mechanisms—latches, the rear handle, etc.
- The windows
- Any of the chrome—the rear taillights, for example
- the rear doors, if they’re salvageable
- Any of the interior mechanisms from these doors—scissors, latches, etc.
- Chrome brightwork, interior steel surround
- Either of the bumpers, if they’re in good shape
- Front wing windows, if they’re OK.
- Steering wheel/column, if I can get it out
I have no idea what the rest of the truck looks like, but I’ll see when we get out there. And even if the whole thing is a wreck it’ll be fun to go looking.