Author: bill

Inspiration

Dan over at the Binder Boneyard posted a picture of a rig he worked on a couple of years ago that I remember lusting after; it started out as a 2WD Travelall that he converted to 4WD, lifted, and did a bunch of other upgrades to. What I’m looking at specifically is the roof rack, which is the setup I’m going for: an eight-point rack with a solid bed and a very minimal rail. Ideally I’d build the metal sections out of aluminum, but that’s a welding skill I don’t currently possess. I’ve got six of the eight drip rail mounts I need, and I intend to spend a cold winter sketching out a plan for the rack itself. I wonder how much a used TIG welder goes for on Marketplace….?

Posted on   |   by bill   |   Leave a Comment on Inspiration  |  Posted in Inspiration, Travelall

Weekly Roundup, 10.29

On Thursday afternoon I got a long narrow package delivered by UPS, which contained a set of headliner bows from my friend Ray up in Massachusetts. He sent a pair of square-end bows like the three I’ve already got in the truck, which were made to work with an aluminum channel around the perimeter of the roof that would hold a headliner in place. My truck didn’t come with a headliner or the channel, just three rusty bows (out of five) and the fiberglas insulation glued to the ceiling.

Below that are five point-end bows which went on earlier model Travelalls without the aluminum channel; from what Ray tells me the headliner tucked in under the sheet metal lip around the edge and these bows held it into place. Because these bows are in much better shape than the square-ends I’ve got, I’m going to clean them up and use them when I build and install a headliner.

Meanwhile, I got another big box in the mail via UPS, in which was packed a primer black ’57 Ford F-150 bumper. I brought it out to the truck and laid it on top of the C-series bumper, and apart from the fact that it’s a little narrower, I think this thing will work very well.

I’ve got to figure out how to build a set of sturdy standoffs from the frame horns on the front of the truck—the current standoffs are 4″ deep sections of box channel steel held in place with some long rusty bolts and a wheelbarrow full of washers. I’ll probably do something similar but gusset the boxes for strength.

Saturday morning I went to Bennett’s to help him swap out the rear brake line on his Speedster replica; he’d taken it to a car show earlier in the year and blown the line on the way home. It turns out the manufacturer ran the brake line inside the cabin along the transmission tunnel, ending in a fitting directly behind the driver’s seat. After some careful application of heat and penetrant we got the fitting off the distro block behind the front suspension and cut a new line with some extra length to spare. Bennett then showed me how to make a bubble flange on a brake line, which I’d never seen before, and we installed the new line and bled the brakes.

With that success, we took a test drive to Ellicott City for some barbecue and brought it home to eat in the warm sunshine.

A couple of weeks ago I saw an ad pop up on Marketplace where a guy had a storeroom full of old IHC R-series parts he was selling, and I alerted Bennett. He’d driven up there a couple of weeks ago and picked through the stuff, coming home with a box full of NOS parts for Phantom, his ’53 R-110 pickup. Before I left, we looked through the box of stuff he brought home, and he handed me an NOS doorhandle and window crank for a C-series pickup in perfect shape. I’ve got to figure out what they’re worth and give him some cash the next time I see him. He also had a trio of black NOS armrests in original IH packaging—the foam on the backside was bright yellow like the day they were made—and sent me home with one to see if it fit Peer Pressure. I already have a black set on the truck, but maybe I’ll buy two of these to put in the spares box along with the used ones that look like they were fished out of a river.

Addendum: I forgot to mention that I ran the engine up for about ten minutes on Saturday when the girls were out of the house (the exhaust is super rich and tends to flood the house, so I wait until they’re away) and got it up to temperature. It only took two pumps of the throttle to get her fired up, which was encouraging. Looking at various points of the engine with a laser thermometer, the manifold junction on the driver’s side got to about 450˚, while the passenger side got to 520˚. I then remembered that the coolant was low so I waited until the water neck hit about 160˚ and decided to shut it down, so I don’t know if the thermostat is working yet or not. I added about 3/4 of a gallon of coolant and let it cool down before putting the cover back on. It’s sounding a little clattery but the idle smoothed out after awhile; I think the rings need to come loose and seat properly after sitting for so long, and I need to have a professional tune the carb properly to get her running right.

Posted on   |   by bill   |   Leave a Comment on Weekly Roundup, 10.29  |  Posted in Friends, Repairs, Travelall

Weekly Roundup, 10.21

I had a chunk of time on Sunday to get outside in the blustery sunshine and keep working on things. The first project was to weld a set of plates to the back of the seat box to use for mount points on the vertical section of the step. I ran out to a local independent welding shop on Friday and got a tank exchanged for much less than Airgas charged me last time; I was happy enough with their service that I opened up an account to save the extra $15. And, they’re open on Saturdays.

Back in the garage, I had a bunch of 18 ga. scrap left over from bending the doors and I used a section of that to add some stiffness. I cut two rectangles out and welded them in place, then sanded the high points down and prepped the whole thing for etching primer. First I covered all of the welds that were impossible to reach with the wire wheel with rust encapsulator and then let it sit outside with primer to cure. The next step will be to prime it, put some guide coat on the flat surfaces sand it lightly to find the high and low spots, then fill those and get things cleaned up for paint.

In the truck, I decided to do a little archaeology and see what was under the weird rubberized coating on the driver’s floor. I used the wire wheel to grind out the edges and revealed a series of 1/2″ spot welds around the perimeter, which should be pretty easy to grind out and replace. The metal is, predictably, lousy the closer to the pedals it gets; moisture stuck under the rubber mat did a number on the “repair.

Elsewhere, I pulled the driver’s rear wheel off, got on the creeper and continued knocking rust off all of the rear frame elements I could see with the needle scaler, and then covering it all with encapsulator. I think I’ve got about 80% of the rear finished; I need to do the same with the passenger’s side and do all of the vertical surfaces over there. Finding true marine-grade plywood in stock locally has been a challenge, but Brian tells me there’s a brand at Home Depot that’s essentially the same thing: 7-ply Douglas fir made with waterproof glue. I’ve got to find it in stock locally and pick up a sheet this coming week.

A reader named Mike wrote me last week and offered a parts list he compiled while building a ’67 1100 with a 304; essentially the same truck I’ve got, but with an auto transmission, power steering and brakes. He was kind enough to share it with me this morning, and I’ll definitely put it to good use. Thanks Mike!

Posted on   |   by bill   |   Leave a Comment on Weekly Roundup, 10.21  |  Posted in Progress, Travelall, Welding

Locked Box

I spent most of Saturday sitting on the couch while my COVID vaccine made me feel sore and loopy, but it rained all day so I wasn’t that upset. Sunday was partly cloudy but not actively raining, so after getting the dog out for a walk and doing some small errands, I got back out to the garage to keep working. At this point the box project is just finishing up small details; I got a set of locks from Amazon and had plans for how the doors should close.

The plan was to weld in a set of doubler plates underneath to add support, then carefully cut holes in the doors and widen them on two sides to accept the lock barrels, which are notched on either side to prevent them from spinning when the key is inserted. After doing a test run on scrap metal, I got this done pretty easily and used one of Dad’s old files to widen the holes. After burning them in, and test-fitting everything, I carefully cut notches in each of the square tube to accept the latch arms. The passenger side was just short of the arm so I had to add a small plate on the face of the square tube to catch it.

I did some experimenting with thin strips of metal to see what I liked for doorstops, but everything I had seemed way too big or wide to work. Conscious of avoiding anything with sharp edges, I settled on a length of 1/4 rod from a different project. I cut 6″ sections and welded them at the lock ends, then ground down the high spots so that everything is smooth.

Next, I wanted to reinforce the hinges, so I drilled three holes through the plate inside the box and welded the resulting hole shut. This way each hinge is borrowing from the plate but I’m not adding ugly beginner welds to the outside edges.

Finally I put a plate in between the two hinge bars from the bottom to make a shallow tray for tools or other gear. I’ll cut a rectangle of floormat to go in there after things get painted.

I’m almost ready for paint. The last thing to be done is to weld in a set of gussets/mounting points on the backside that will go through the vertical wall on the rear step. Out of curiosity I called a powdercoating shop nearby and was quoted $100 from a disinterested shop foreman, so I think I’ll stick with my budget rattlecan approach. So now I’ll practice my sanding and filling skills to clean up the outside.

Outside in the truck, I pulled the wood floor back up and kept grinding at the rust. The needle scaler did all the work, and I made it all the way forward up the frame to the rear step. I was able to get encapsulator on everything before I had to close up for dinner, and I left the floor out of the truck to air it out. I have to pull each rear wheel in order to reach the outside of the frame rails completely, but I’ve gotten to most everything I can with the floor up.

After calling Super Scout Specialists twice in two weeks to inquire on having a new dash wiring harness built, they told me the guy who builds their harnesses is two months behind and hasn’t been in the shop in two weeks. I thought about it over the weekend and figured I’d better place an order now to get the thing sometime this year, as I haven’t found anyone else building them for a competitive price (scoutparts.com wants to charge an extra $3-400 over what SSS is asking; no thanks.) I’ve actually got a harness from a ’68 pickup on the bench downstairs, so I theoretically could swap it in for what I have; I don’t know whether or not they updated circuits between ’63 and ’68, though. Wiring this thing is going to take a lot of time and learning.

Meanwhile, my friend Ray from the BP has a set of five headliner bows up in Massachusetts he’s going to sell me, which should provide a solution to a future problem: what to do with the insulation glued to the ceiling, and how to cover that up. There’s an aluminum J-channel in later Travelalls that acted as a trim ring but from what he tells me it’s very hard to remove and would be impossible to ship. I think I might experiment with some thin Luan covered with fabric and use these bows to hold things up.

Posted on   |   by bill   |   Leave a Comment on Locked Box  |  Posted in Repairs, Travelall, Welding

Painting Your Beater

Here’s a real nice video from Eastwood going over the basics of how to paint your beater in the driveway without blowing it apart into one million pieces. There’s a lot of good information in there—some extra steps on body filler and sanding that I -ahem- have skipped over, etc. As I look toward the spring and painting the roof of the Travelall, this will come in real handy.

Posted on   |   by bill   |   Leave a Comment on Painting Your Beater  |  Posted in Paint

Weekly Roundup, 10.8

The beginning of the week was quiet, but I put almost two full days in over the weekend.

With the glass and other stuff out of the back of the Travelall, it’s much easier to start some of the preventative maintenance I’ve wanted to do to the rear frame and crossmembers. Saturday afternoon I lifted the rear bench seat out and pulled up the plywood floor. Then I put on some ear protection, fired up the compressor and the needle scaler, and got to work. Starting from the back I took as much scale off the unpainted metal as I could find, making my way to an area over the rear axle. Then I brushed on Rust Converter to everything I’d cleared and let it sit. I started around 4 and finished when the sun was setting, so there’s still a lot more to do—and I haven’t even touched the underside yet—but it’s already looking much better under there.

Reorganizing the garage a bit, I stumbled across an extra box of weatherstripping and realized it was doing me no good here. So I put it up on Marketplace and got a pretty immediate response from a guy in Washington, who was also interested in my old brake booster until I did the research and learned it would be something like $80 to ship it out to him in Washington. So the windshield gasket is on its way to him, and the brake booster remains in the Heavy Metal corner of the garage next to the old starters, spare Dana 20, and other stuff.

A brake has been instrumental to the plans I drew up for the doors on the seat base, because I wanted to bend a quarter-inch of metal along the edges on the three sides to add structural stability and make it look better. My Harbor Freight brake is woefully unprepared to bend 18 ga. metal at the measurement I need. On Sunday I met up with Bennett over at our friend Brian’s shop to get a couple of projects done. Bennett was there to clean up the carburetor on his Hudson project as well as tinker with Heavy D, which has been sitting there for several months waiting for a windshield replacement. I was there to use the heavy-duty finger brake Brian inherited with the pole barn shop on his property.

I started messing with the brake and putting a couple of scrap pieces through it to learn how it worked and where the sweet spot was. There was only one finger clamp on it, so the first long section of metal I bent didn’t stay still and bent unevenly. I took a break, had a donut, and Bennett suggested looking around the shop for the other fingers. I found them along the back wall and installed three of the fattest I could find, then put another long test sheet through. When those results looked much better, I marked out some new metal and started bending. We had to do some creative adjustment to the brake, because the bending plate was so close to the lever plate it wouldn’t release the metal when I’d bent the second side. This involved unscrewing the plate from the bottom to release my metal, but it worked. After I got two doors bent and test-fitted, I helped Bennett mess  around with Heavy D, got it started for the first time in forever, and installed a choke cable before we both headed for home.

Back at the house, I investigated how I could bend the short edge with the tools on hand. I’ve got a cheap wide vise I bought from Harbor Freight back in the day, and after some testing I realized I could bend the width I needed with that and a pair of vise-grips blocked into place, keeping the entire width of the metal on basically the same plane. After making the initial bend, I had to hammer the center sections flatter with a combination of deadblow hammer, wood blocks, and metal scraps. When I had it flat and straight, I welded the corners up, cleaned them up with the flap disc, and trimmed the length of each to allow for the width of the hinge knuckles.

When those were in place, I tacked the hinges in place and test fit the doors; all my cuts looked good. So I flipped the hinges, cut some tack holes in the doors, and welded those into place. If I had to do it over again, I’d have put the weld on the underside, but I think it looks pretty good either way.

So the doors are in place, and next I need to cut and install a pair of stops opposite the hinge side for the doors to sit on. I’m going to wait until the locks come in next week so that I can design around those. I was originally going to cap off that gap in the middle, but now I’m considering adding a plate underneath to make it a shallow tool well to utilize some dead space.

The other thing I spent a bunch of time looking for last week was a hinge of the proper size for mounting the seat to the box. The hinges on the seat base are beefy; the pin is 3/8″ in diameter and the knuckles are thick. I found a lot of hinges with the right pin size but nothing with a leaf the proper length—the interlocking sections of the hinge I’ve got are 1.5″ wide, and most industrial hinges I’ve found with that pin size are only 1″. While I was at Brian’s, I was looking at his scrap pile and found a beefy hinge with a 3/8″ pin and a 2″x2″ leaf—exactly what I had been looking for. I texted Brian about it and he told me to take it with me.

Monday I had off for Columbus Day, so I got back outside and kept rolling. First I cut two hinges down to the right size, trimmed the knuckle widths, and test fit them on the box. When I liked what I saw, I tacked them in and fit them to the seat. With that confirmation I burned them both into place and cleaned up the welds. The plates will get two bolts through the square tube for extra structural support, but I like where things are sitting (literally) now.

Then I got out the needle scaler and wire wheel and continued working on the chassis while I had the rear floor out. Before finishing up for the day, I brushed on some Rust Encapsulator. I’ll finish coat it with chassis black when it’s all ready, but there’s a lot more to go.

Meanwhile, I’ve tried removing old upholstery adhesive on the vertical surfaces with every chemical I can think of and a rubber eraser wheel with no success. Frustrated, I tried a small patch with the wire wheel and found that with a very light touch I could get most of the old crust off without going through the paint to metal—there are a few places where the paint is very light—but it mostly came off with little damage. I was always going to respray the inside anyway, so I’m not worried about patchy areas. It’s nice to have that stuff cleaned up, for sure. I’m going to see if Hobo Freight sells a plastic bristle wheel for an angle grinder and see if that’s more gentle on the paint.

Posted on   |   by bill   |   Leave a Comment on Weekly Roundup, 10.8  |  Posted in Friends, Seats, Travelall, Welding

Market Research

A Travelall popped up in Pennsylvania on Marketplace yesterday, and I of course clicked to take a closer look. It’s a 1962 4×4 with a transplanted 392 in the engine bay, and originally came from Colorado. There’s only one shot of the inside and none of the engine bay. It’s got a liberal coating of what the kids call “patina”, which is to say, the Colorado sun blasted off all of the paint on the horizontal surfaces. There are a couple of underside shots which look very similar in condition to the red bus in my driveway, and there’s rot in the front fenders in the same places. The seller wants $17,500.

As a 2WD, my truck isn’t quite as desirable, but if I can get the red bus up and running for half of that cost, I figure I’ll be far ahead of the market.

Posted on   |   by bill   |   Leave a Comment on Market Research  |  Posted in Inspiration, Travelall

Boxed, Part 3

This weekly update is regrettably several days past my usual Friday schedule, but given the amount of stuff I’ve been posting this year, I figure that’s OK.

With winter fast approaching and a week and a half worth of wet weather behind us, I knew I was going to have to do something about dry storage for the Travelall. Erecting a new garage is out of the question, and putting the awning up isn’t going to fly, so I went with the cheapest option: an inexpensive Suburban-sized car cover from Amazon. At first I was afraid it wasn’t going to be big enough to cover my truck’s ample backside, but once I adjusted the front, the rear fit snugly over the taillights with little to spare. It’s tight enough that I don’t even think I’d need to tie it down, although having two built-in straps is a nice feature.

On Sunday I had the afternoon to keep working on the seat cage, so I finished cleaning up the joins and smoothing everything out. Then I put it in the truck, taped a rectangle of cardboard to the top, and scribed out the trans tunnel. With some adjustments and a second template, I laid it on some 18 ga. steel and cut out the front section. After I trimmed it to where I liked things, I tacked it in place and did one last check before tacking the perimeter in place every inch.

When I’d ground down the welds, I cut out two rectangles for the ends and tacked those in. I did another test fit, ground some things down, and tacked each side into place.

Then I adjusted the welder settings, sealed up the top and sides, and ground everything down to smooth with the flap disc. At this point I’m trying to figure out how I’m going to arrange the two doors; currently I like the idea of countersinking them inside the cages that they’re flush with the top. I’ve got a hinge here from Grainger ready to go, but the locksets they sent me are way too small (curse you, Internet!). So I’ll spend some more time considering that solution.

The other thing that came in the mail were two 3D printed plastic visor clips, something the truck didn’t come with and that I haven’t seen anywhere else. I took a chance based on a comment from the Round-Body Travelalls group on Facebook, and I was not disappointed when they showed up. With two stainless screws from my bench stock, the clip went right into the existing holes on the driver’s side and the visor snapped into place. They need to be sanded and cleaned up, but I’m happy.

Posted on   |   by bill   |   Leave a Comment on Boxed, Part 3  |  Posted in Seats, Travelall, Welding

Roadworthy

With the weather getting colder, my chances to take the Scout out on long trips get slimmer. Looking at the forecast Saturday morning, I knew it would be iffy, but I haven’t had her out on any adventures pretty much all year due to the exhaust leak. Now that she’s fixed, I figured I’d take her on a shakedown run to my father-in-law’s house to see how she ran. The short answer is that she did great. We covered 200 miles with absolutely no problems at all; the engine is strong and smooth and sounds great, just like I remember. It was overcast in the morning so I decided to take the top down and pack the bikini top just in case, but I wound up leaving it down for the whole day.

Choosing the Scout for a trip like this basically comes down to convenience versus fun. The Hondas are dry and climate controlled, and obviously the gas mileage is better. The Scout requires advance planning and a keen eye on the weather. I reviewed the forecast carefully this morning and saw that there would be sun down south, so I made sure to pack wet weather gear, a pair of shorts, and a fleece. What I didn’t remember was a warm hat of some kind, so when I left my FIL’s house I stopped at the local Marshall’s and picked up a cheap one. I wound up putting it on about 20 miles up the road, and stored it in the lockbox between the seats, where it will now be the truck hat.

I will say that in a lot of ways, the Scout is a superior vehicle for long-distance travel than the Accord. The seats are nicer (thanks, Chrysler!), the wheel is much more comfortable, and the seating position is better. I can see around me better for obvious reasons. Steering is two-finger thanks to power steering; the only thing that gets funky is hitting expansion joints at freeway speeds and sudden braking; the left side is grabbing before the right, which requires some careful adjustment.

These days, I get more and more looks from people. I had a guy roll up next to me in a pickup at a light and ask how old it was. A black dude in a slammed BMW wagon pulled up alongside and gave me a thumbs up; I pointed back at him and returned the sentiment. A couple of dudes in a big white work truck honked and waved as I overtook them.

Some small issues: I noticed that the temp gauge isn’t working anymore, so I’m going to swap out the temp sender and see if that makes a difference. I had to use the wipers coming back up 695 into Catonsville (home by the hair of my chin) and saw that the secondary arm on the driver’s wiper isn’t connected anymore, so I need to get a new retainer clip for that. The headlights definitely need to be adjusted, but they’re still very dim. An LED upgrade might be in order next year.

Overall, I’m thrilled to have her back on the road, and I can’t wait to have some more adventures.

Posted on   |   by bill   |   Leave a Comment on Roadworthy  |  Posted in Trip Logs